Calculating Scale 计算比例

Scale is an important part of Architectural Drawings. The definition of scale according to the dictionary is:
比例是建筑绘图非常重要的一部分,在字典里“比例”的定义如下:

Scale 比例:
With a uniform reduction or enlargement. In proportion to the surroundings (of a drawing or model): Example: It is hard to build models to scale from a drawing.
统一的缩小或放大图形,与其实际相应图形的线性尺寸之比
例句:很难根据图片按比例制作模型。

When making Architectural Drawings it is very important that the proportions of object remain the same. It is also important to understand how sizes relate when enlarged or reduced. Reduction in scale is common in Architecture, as it would not be possible to draw a building on paper at the size it will be built. Therefore all the measurements are reduced.

在制作建筑绘图时一定要注意物体的比例是保持不变的,还有当放大或缩小比例时的关系。在建筑中缩小比例是非常常见的,因为想按照建筑原来的大小在图纸上是画不下的,所以要缩小比例。

Scale is easy to calculate using the metric measuring system. Metric measurements are used by most countries around the world. The Metric System is very easy to use. As you move up and down the scale you simply move the decimal place. Imperial Measurements are used in America. Canada Uses both Metric and Imperial Measurements because of the close relationship with America. Imperial measurements are much more difficult to calculate because fractions and irregular intervals are used when converting between the various measurements in the scale.

很多国家都使用公制度量衡,用公制度量衡单位来计算比例是非常简单的,当你想增大或减小比例只要变动一下小数位就行了。在美国使用的是英制度量衡体系,加拿大由于跟美国关系密切所以两种度量衡体系都使用。英制体系要更为复杂一些,因为在换算比例时小数和不规则的间隔很多。

Look at the Measurement scales for both the Imperial and Metric measuring systems. There are many units of measurements. The 4 most commonly used measurements are shown in RED.

请看下列两种测量单位,请看下列两种度量衡单位,每一种都包括很多小的单位,其中最常用的四种已用红色字体标注出来。

Metric Measurement Scale 公制度量衡单位

Kilometer千米1,000
Hectometer百米100
Decameter十米10
Meter1
Decimeter分米0.1
Centimeter厘米0.01
Millimeter毫米0.001
Micrometer微米0.000,001
Nanometer纳米0.000,000,001

Imperial Measurement Scale (America) 英制度量衡单位(美国)

Mile (8 Furlongs)英里(8弗隆)63,360
Furlong (10 Chains)弗隆(10链)7920
Chain (22 Yards)链(22码)792
Yard (3 Feet)码(3英尺)36
Foot (12 Inch)英尺(12寸)12
Inch英寸1
1/2 Inch1/2 英寸0.5
1/4 Inch1/4 英寸0.25
1/8 Inch1/8 英寸0.125
1/16 Inch1/16 英寸0.0625
1/32 Inch1/32 英寸0.03125

Determining Scale 确定比例

Determining scale is very important for Architectural Drawing and model building. Scale is shown as a ratio between two different sets of dimensions. (The dimensions of the actual object, and the reduced or enlarged dimensions of the drawing or model). The formula for determining scale is simple. However remember that you might need to convert numbers to the same unit of measurement. Converting Metric Units of measurements only requires moving the decimal place, where converting Imperial units will be more complicated. 

在绘图时确定比例是非常重要的一步,比例是指两个不同维度之间的关系(物体原本维度及被放大或缩小后的维度)。确定比例的公式非常简单,但是要注意单位的统一。公制度量衡体系只需移动小数点位置就可以了,而英制度量衡则要复杂多了。

To calculate scale you must know the following:
在计算比例时需了解以下:

S = Scale  比例
AS = Actual Size  实际大小
MS = Model Size  模型大小
Scale = Actual Size / Model Size
比例 = 实际大小 / 模型大小

Example  例子

A model car that you bought is 20 centimeters long. The car is 3 meters long in real life. What is the correct scale of the car model?

你购买的模型车长20厘米,而该车的时间长度是3米,那么该模型车的比例是多少?

Step 1: Covert meters to centimeters
第一步:把米转化成厘米

3 meters = 300 centimeters
3米 = 300厘米

Step 2: Calculate scale
第二步:计算比例

Scale 比例 = 300 / 20 
Scale 比例 = 15

Therefore 1 centimetre on the model is equivalent to 15 centimetres on the real car. This is also written as a scale of 1/15

所以该模型的1厘米相当于实际的15厘米,该比例写为1/15。

Practice Activity 练习活动

The Eiffel Tower in Paris France is a cultural landmark. The Eiffel tower is 300 meters tall. At the gift shop you can buy model replicas of the tower that are 20 centimetres tall. Determine the scale of the model. Show all steps of your calculations.

法国的埃菲尔铁塔是一个著名的地标。该塔高达300米,而在礼品店你可以买到20厘米高的模型。请你计算该比例是多少,并写出步骤。

Calculating Scale Vocabulary 计算比例词汇

Area面积
Beam (width of a ship)船宽(船的宽度)
Centimeter (cm)厘米(cm)
Conversion转换
Feet (Plural form of foot)英尺(复数形式)
Foot (Singular form)英尺(单数形式)
Height高度
Imperial Measurement英制度量
Inch英寸
Meter  (m)米 (m)
Metric Measurement公制度量
Model模型
Scale比例
Size (Actual Size or Model Size)大小(实际大小或模型大小)
Width宽度

F-16 Fighter Jet (Falcon) – Calculating Scale Task
F-16战斗机(Falcon)任务

The F-16 Fighter jet also knows as the Falcon was a lightweight fighter jet developed in 1976 for the United States Air Force (USAF). It quickly evolved into a successful multipurpose aircraft. This aircraft had numerous innovations such as a frameless bubble canopy for better visibility.

F-16战斗机又名为Falcon(猎鹰战斗机)是1976年美国空军(USAF)研制出的一种轻型战斗机。随后演变成一架多功能的飞机。该飞机融进了多种新科技,如为了获得更好地能见度使用了无骨架舱盖。

The plane weighs 8,570 kg (Kilograms) and is 15.06 meters long. The plane  has a wingspan of 9.96 meters and and the total area of the wings covers 27.87 m2. The F-16 is capable of speeds of 2,410km/h. If traveling at the planes top speed an F-16 could take off in Beijing and land in Shanghai 1,069 km away in under 30 minutes. This is an impressive plane which has been a very important part of American Aviation.

该飞机重达8,570千克,长达15.06米,机翼长达9.96米,且机翼面积达到27.87平方米。F-16失速可达2,410千米/时,如果从北京出发到上海只需30分钟。 在美国航空史上这架飞机起了至关重要的作用。

A scaled model is 20.1 cm in length and want to know the scale. Calculate the following questions about this model airplane and determine the scale ratio.

现在已知模型长度是20.1厘米,那么该比例是多少。计算下列关于该飞机模型的问题和比例。

F-16 Fighter Jet (Falcon) F-16战斗机

1. How long is the F-16 Fighter Jet? (Meters)
该 F-16战斗机多长?(米)

2. Convert the length of the F-16 from meters to centimetres
把 F-16战斗机的长度从米换算成厘米。

3. What is the length of the F-16 Model
F-16战斗机模型的长度是多少?

4. Calculate scale. (Show all steps in your math)
计算该比例。(写出具体的步骤)

  1. Now that you know the scale calculate the following dimensions of the model. Convert the scale of the model from centimetres to the “American Imperial Measurements”. 1 centimetre is equal to 0.3937 Inch.  Round your answer to 1 decimal place.
    根据你所得出的比例来计算该模型的其他规格。最后把比例从厘米换算成“英制度量衡单位”,1厘米等于 0.3937英寸,且答案保留1位小数。
Dimensions 规格Meters Centimeters 厘米At Scale 模型大小Conversion 换算
Length 长度15.06 m1,506 cm20.1 cm7.9 Inch
Width 宽度4.88 m
Hight 高度
Wing Area 机翼面积

The Titanic – Calculating Scale Task
泰坦尼克号任务

The RMS Titanic was one of 3 Ships built by “White Star Line” as part of their “Olympic Class Ocean Liners”. These three ships were the most luxurious ships ever built until that point in history. The “Titanic” was the most impressive of all the ships. It was larger, more luxurious and was thought to be “UNSINKABLE” since it was designed with water tight doors dividing the ship. If the hull was damaged the water tight doors would contain the leak in that area of the ship which would prevent the ship from sinking. 

RMS泰坦尼克号是“白色航运公司”建造的“奥运类远洋航班”中的3艘豪艇中的一个,这3艘船在当时是最为豪华的,而泰塔尼克号是其中最令人叹为观止的。她庞大、豪华,被认为是“永不沉没的”,因为整艘船被水密门隔开。如果船体被损坏,水密门会保存船上进入的水而阻止船下沉。

The Titanic was famous for its innovation, but the Titanic is not remembered today for its Engineering marvels but the devastating maiden voyage. The Titanic, the “UNSINKABLE” ship, sank on April 15th 1912 on its first crossing from Southampton in the  United Kingdom to New York City in America.

泰塔尼克号因其设计新颖而出名,但是现今并不是因为其工程浩远被人铭记,而是其一次毁灭性的海上航行。1912年4月15日,这艘号称永不沉没的船在其从英国的南安普敦到美国纽约的处女之行中沉入了海底。

There were 2,224 people aboard the Titanic when it set sail for America. Only 710 passengers were saved the night the Titanic sank. 1514 passengers lost their lives.  There were only enough life boats for half of the passengers aboard. Even with the limited amount of lifeboats many of the life boats were only half full when they were lowered into the ocean. Many lives could have been saved, however many people thought that the boat could not sink. After the Titanic disaster, recommendations and changes were made to improve passenger safety. Mandatory life boat drills were implemented and the amount of life boats aboard a ship was increased to accommodate every passenger aboard.

在这艘开往美国的泰塔尼克号上有 2,224乘客,在其沉没的那晚只有710个幸存者,其他1514个乘客全都丧身海底。当时仅有能救一半乘客的救生艇,更糟糕的是这些救生艇并没有坐满,因为他们都相信这是一艘永不沉没的船。在这次灾难之后,海上航线考虑到乘客的安全做了很多改善,并进行了多次的强制性就生演习,同时也增加了救生艇的数量。

pastedGraphic_3.png
The Titanic 泰坦尼克号

The Titanic was 269.0 meters long, and weighted a total of 52,310 tons. The Titanic was propelled by two 3-blade propellers and could travel at speeds of 44km/h. A scale model of the Titanic is available which is 67.25 centimetres long. Calculate the model scale: (Show all your calculations)

泰塔尼克号船长 269.0米,重达 52,310吨,并使用了3叶的螺旋桨, 其航行时速可达44千米/时。现有泰塔尼克号模型一个,其长度是 67.25厘米。计算该模型比例。(写出具体计算步骤)

Using the scale ratio you calculated determine the height of the actual Titanic by using the measurements of the model. If we use division to calculate the size of a reduced model what formula would we use  to calculate the size of the original from measurements from a model?

已知模型的高度,根据你所得到的比例,计算泰塔尼克号的实际高度。如果我们使用除法来计算模型的大小,那么现在知道模型的大小来计算实际大小应该使用什么公式?

Dimensions 规格The Titanic 泰塔尼克号Scale Model 模型大小
Length 长度269.0 m or 26,900 cm
Height 高度13.235 cm
Beam 船宽7 cm
*Beam is the term used to describe the width of a ship at its widest point.
*船宽指船的宽度,在英语中用beam这个单词来表示。

Now that you have calculated the dimensions of the Titanic in Metric convert the units to Imperial Measurements.

现在你已计算出泰塔尼克号规格了,下面把公制度量衡单位换算成英制度量衡单位。

Dimensions 规格The Titanic (cm) 泰坦尼克号(厘米)Convert to Feet and Inches 转换成英尺和英寸

Length 长度

26,900 cm

26,900 cm X 0.3937 cm/inch 10590 inch
12 inch/foot
10590 inch ÷ 12 inch/foot 882.5 feet
.5 feet X 12 inch/foot 6 Inch
882 Feet 6 Inches
Height 高度
Beam 船宽
*Beam is the term used to describe the width of a ship at its widest point.
*船宽指船的宽度,在英语中用beam这个单词来表示。

Course Navigation

Go to the course homepage

Go to the previous lesson

Go to the next lesson

Download activities to use in your classroom